INSTALLATION INSTRUCTIONS FOR PART 95-7801
APPLICATIONS
See Application List Inside
95-7801
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Units Provision
KIT COMPONENTS
• A) Radio Housing • B) Rear Support Tray • C) ISO Brackets
• D) Mounting Bracket (Acura legend) • E) (2) #8 x 1/2” Phillips Pan Head Screws
• F) (6) #6 x 1/4” Phillips Flat Head Screws
B
A
C
D
E
F
TOOLS REQUIRED:
• Phillips Screwdriver • Cutting Tool
1-800-221-0932
© COPYRIGHT 2001-2008 METRA ELECTRONICS CORPORATION
95-7801 DASH DISASSEMBLY
ACURA CL 1997-1999
A
1
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
2
Unclip the radio trim bezel and disconnect the
clock and climate control wiring. Remove (2)
8mm hex-head screws securing the factory
head unit and disconnect the wiring. (Fig. A)
3
Cut and remove all mounting clips on the Radio
Housing EXCEPT clips "A" and "H". (Fig. B)
Skip to step #3b on Page 10.
B
"A"
"A"
"H"
"H"
ACURA INTEGRA 1990-1993
1
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
A
2 Remove (3) screws from each side of the center
console and remove the console. Remove (2)
screws securing the factory head unit to the
sub-dash support bracket. Slide the head
unit/pocket assembly out and disconnect the
wiring. (Fig. A)
3
Cut and remove the mounting tabs from the bot-
tom of the Rear Support Tray (Fig. A). Cut and
remove all mounting clips on the Radio
Housing EXCEPT clips "C" and "H" (Fig. B).
Skip to step #3b on Page 10.
2
B
Fig. A
"C"
"C"
Fig. B
"H"
"H"
1
95-7801 DASH DISASSEMBLY
ACURA INTEGRA 1994-2001
1
2
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
A
Remove the cover cap located under the emer-
gency brake and remove (2) screws exposed.
Remove (2) screws from the rear corners of the
lower dash trim bezel and remove. Remove the
ashtray and (2) screws exposed. Unsnap the
ashtray housing and disconnect the cigarette
lighter harness. Remove the gear shifter knob
and unsnap the shifter trim. Remove (2) screws
below the radio opening and remove the upper
dash trim bezel. Remove (2) 8mm screws secur-
ing the factory head unit and disconnect the
wiring. (Fig. A)
"C"
2
B
Fig. A
"C"
"H"
3
Cut and remove all mounting clips on the Radio
Housing EXCEPT clips "C" and "H" (Fig. A). Cut
and remove the slots on the bottom of the ISO
Brackets (Fig. B). (THE REAR SUPPORT TRAY
WILL NOT BE USED). (Fig. B)
"H"
Fig. B
Skip to step #3b on Page 10.
ACURA LEGEND 1990-1996
1
2
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
A
Remove (2) screws below the ashtray.
Unclip the dash trim bezel. Disconnect the
cigarette lighter wiring and remove the
bezel. Remove (2) bolts securing the rear
of the factory head unit and disconnect the
wiring. (Fig. A)
3
Attach the Mounting Bracket to the bottom of
the Rear Support Tray (Fig. A). Cut and remove
all mounting clips on the Radio Housing
EXCEPT clips "E" and "J". (Fig. B)
B
Fig. A
Fig. B
Skip to step #3b on Page 10.
"E"
"E"
"J"
"J"
2
95-7801 DASH DISASSEMBLY
ACURA TL 1996-1998
1
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
A
Using a small screwdriver, unclip the perimeter
of the radio trim bezel. Disconnect the climate
control and rear defroster wiring and remove
the bezel. Remove (4) Phillips screws securing
the factory head unit/trim bezel assembly.
Loosen (2) Phillips screws securing the back of
the head unit to the metal housing and slide the
unit out. (It is NOT necessary to remove the
screws securing the metal housing to the
bezel). Disconnect the wiring. (Fig. A)
2
Fig. A
B
"B"
Fig. B
3
Cut and remove the mounting tabs (Fig. B) from
the bottom of the Rear Support Tray (Fig. A).
Cut and remove all mounting clips on the Radio
Housing EXCEPT clips "B" and "K" (Fig. B). Cut
and remove the slots on the bottom of the ISO
Brackets (Fig. C).
"B"
"K"
Fig. C
"K"
Skip to step #3b on Page 10.
ACURA VIGOR 1992-1994
1
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
A
2
Remove the access cap from the climate control
cluster and (1) screw exposed. Unclip the clus-
ter and remove (2) screws exposed. Remove the
ashtray and (2) Phillips screws exposed.
Remove the cover caps from each front corner of
the center console and the screws exposed.
Open the storage compartment, lift up the carpet
and remove (2) screws exposed. Lift up on the
center console and remove. Unclip the radio trim
bezel and disconnect the wiring. Remove (2)
bolts from the back of the factory head unit and
disconnect the wiring. (Fig. A)
B
"A"
3
Cut and remove the mounting tabs from the bot-
tom of the Rear Support Tray (Fig. A). Cut and
remove all mounting clips on the Radio Housing
EXCEPT clips "A" and "H" (Fig. B).
"A"
"H"
Fig. B
Skip to step #3b on Page 10.
"H"
3
95-7801 DASH DISASSEMBLY
HONDA ACCORD 1990-1993
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
2
A
Remove (4) screws from the lower portion
of the center console. Remove the gear
shifter knob and lift the console out.
Remove the ashtray and ashtray bracket.
Remove (2) screws from the bottom of the
head unit support, slide the unit out and
disconnect the wiring. (Fig. A)
Cut and remove all mounting clips on the
Radio Housing EXCEPT clips "C" and "H"
(Fig. A). Cut and remove the slots on the
bottom of the ISO Brackets (Fig. B). (THE
REAR SUPPORT TRAY WILL NOT BE
USED).
3
B
"C"
Fig. A
"C"
"H"
"H"
Fig. B
(Fig. B) Skip to step #3b on Page 10.
HONDA ACCORD 1994-1997
Disconnect the negative battery terminal
to prevent an accidental short circuit.
1
A
2
Remove the ashtray and (1) 3/4" #8 Phillips
screw exposed. Open the storage compart-
ment and remove (2) #8 Phillips screws
exposed. Remove the cupholder tray and
(3) #8 Phillips screws inside. Lift the cen-
ter console out and remove (2) Phillips
screws exposed at the base of the dash
trim bezel. Unclip the bezel and remove.
Remove (2) hex-head screws securing the
factory head unit and disconnect the
wiring. (Fig. A)
B
"A"
"A"
Cut and remove all mounting clips on the
Radio Housing EXCEPT clips "A" and
"H". (Fig. B) Skip to step #3b on Page 10.
3
"H"
"H"
4
95-7801 DASH DISASSEMBLY
HONDA ACCORD 1998-2002
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
1
2
A
Unsnap the clock panel, disconnect the wiring
and remove. Remove (1) Phillips screw exposed
in the clock cavity. Remove (2) Phillips screws
below the factory head unit. Unclip the radio
trim bezel and disconnect the wiring. Remove
(4) Phillips screws securing the factory head
unit assembly and disconnect the wiring.
Remove (2) screws securing the factory pocket
to the assembly. (Fig. A)
Fig. A
Fig. B
B
Cut and remove the mounting tabs from the bot-
tom of the Rear Support Tray (Fig. A). Cut and
remove the slots on the bottom of the ISO
Brackets (Fig. B). Locate tabs "A" on the ISO
Brackets for mounting, cut and remove tabs
"B"(Fig. C). Cut and remove all mounting clips
on the Radio Housing. (Fig. B)
3
"A"
Skip to step #3b on Page 10.
Fig. C
HONDA CIVIC 1999-2000
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
1
2
A
Remove (2) Phillips screws from the bottom
edge of the glove box door and remove the door.
Remove (3) Phillips screws from the lower steer-
ing column panel. Pull straight down on the
lower steering column panel and remove the
panel. Remove (2) Phillips screws under the cli-
mate controls. Remove (4) Phillips screws from
the lower dash location. Remove (4) Phillips
screws securing the bottom of the dash trim
bezel/head unit assembly and pull the assembly
out as far as possible. Cut the zip ties securing
the head unit and climate control wires, slide
dash trim bezel/head unit assembly from the the
dash cavity and disconnect the wiring. (Fig. A)
"B"
B
"B"
Cut and remove all mounting clips on the Radio
Housing EXCEPT clips "B" and "H". (Fig. B)
Skip to step #3a on Page 9.
3
"H"
"H"
5
95-7801 DASH DISASSEMBLY
HONDA CRV 1997-2001
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
1
2
A
Open the glove box, squeeze the retaining clips
and remove the stoppers. Lower the glove box
and remove (2) Phillips screws from the left
edge. Remove (2) Phillips screws from the lower
steering column panel and remove. Unclip the
lower console cover (below the ashtray and
pocket) and remove. Remove (2) Phillips screws
from the base of the center console, open the
console pocket and remove the (4) outer screws
exposed. Unclip the center console and remove.
Remove (2) Phillips screws securing the radio
trim bezel, disconnect the wiring, and remove
the trim bezel/head unit assembly. Remove (4)
Phillips screws securing the head unit to the
bezel and remove. (Fig. A)
B
"B"
Fig. A
"B"
"H"
"H"
Cut and remove all mounting clips on the Radio
Housing EXCEPT clips "B" and "H" (Fig. A). Cut
and remove the slots on the bottom of the ISO
Brackets (Fig. B). Skip to step #3a on Page 9.
3
Fig. B
HONDA CRV 2002-2006
Disconnect the negative battery terminal to pre-
vent an accidental short circuit.
1
2
A
Remove (2) Phillips from the bottom edge of the
radio trim bezel. Unclip the trim bezel and
remove. Remove (4) Phillips screws securing
the factory head unit and disconnect the wiring.
(Fig. A)
3
Cut and remove all mounting clips on the Radio
Housing EXCEPT clips "C" and "H". (Fig. B)
Skip to step #3a on Page 9.
B
"C"
"C"
"H"
"H"
6
|